Table saws don’t need to be pricy. In fact, you can spend much less than $1000 and still get a great table saw.
The DeWalt Table Saw DWE7485 is the best saw under $1000 I could find. You’ll love all of the features it includes while still being able to rip 2x4s with ease.
If you’re on a budget and don’t need a ton of power, the Rockwell BladeRunner X2 is a great choice.
Below you’ll find the three affordable table saws reviewed. Before you make your decision, read through and find the one that suits your needs.
Let’s get started!
Our Top Picks
Best Table Saw Under $1000
For the price, this DeWALT table saw is impossible to beat with its plethora of features.
- 24.5 inch capacity
- Vacuum attachment
The DeWalt Table Saw DWE7485 is a perfect table saw for professionals or serious hobbyists that need to take their craft to the next level.
You’ll have no problem ripping 4/8th sheets of plywood right down the middle with this bad boy. The fence has a detachable mechanism that will allow you to have 24.5 inches of rip capacity.
Also included in the rip fence is a ledge that will hold anything you’re cutting, so you won’t have to worry about unstable material when ripping.
Changing the blade is easy, all you need to do is detach the lugnut and you’ll be able to access the blade should you need to change it.
The 8-1/4-inch blade also will be cheaper in the long run over 10-inch table saws to replace.
You’ll also be able to access the anti-kickback mechanism should you choose to use it.
You get 2.5 inches of depth from the blade, sufficient for most on-site jobs and hobby projects.
The blade also has material packed around it that reduces any sawdust from getting into the internals of this table saw. This prevents any future jams that prevent you from getting work done.
You can also adjust the tilt of the blade so you can cut the material at an angle. It also has a guard for the blade that will keep you safe.
The blade guard has a vacuum attachment for easy cleanup. On the back, you’ll also find another vacuum port to attach a shop vac.
Unfortunately, one downside is that the riving knife is hard to adjust and can be out of alignment. You’ll have to play with it to get it adjusted properly, you’ll need a 5/32″ Allen wrench to align it properly.
Some purchasers also mentioned that the on/off button on this table saw is a bit small. While this is a very minor detail, it can be a bit annoying when you are used to easy access.
If you’re a professional or serious about taking woodworking to the next level, this table saw is perfect. It’s not even close to the top end of $1000, and it’ll get almost any job you need to do right at home.
- Affordable but also packed with features
- Great for professionals or serious woodworkers
- Riveting knife can be hard to adjust
- On/off button can be a bit small
Also Great Table Saw Under $1000
Combined with the stand, this is one of the best deals for a table saw out there.
- 30 inch rip capacity
- Easy blade change
- Anti-kick back features
This table saw is a little pricier, but also one of the best table saws under 1000. It has a 10-inch blade over the 8 inch DeWalt giving you a higher cutting capacity. If you’re ripping wood all day long, this might be the table saw you need in your life.
You’ll be able to enjoy the 15 amp saw with 4 horsepower which will cut any fine or rough material with ease.
The rip fence also comes with material support so you won’t need to hold anything up while cutting.
You’ll love the 30inch rip capacity as well for when you have a ton of wood that needs cutting.
The arbor lock is a nifty feature, it allows for easy blade changes with the wrench that’s provided.
The smart guard system also works to protect you with the riveting knife and anti-kickback features which will allow you to get a perfect cut every time.
This table saw also comes with a gravity-rise wheel stand making it amazing for job site use. The DeWalt model doesn’t come with the stand, so you’ll need to account for that if you need to use it on the job.
At nearly twice the DeWalt price, it is a hefty investment. If you are a professional and will make use of your table saw, you might find that this model suits you better.
Sadly the start-up can also be a bit slow which can be a negative if you’re in a hurry but it’s a minor issue.
The Bosch 4100XC-10 is going to cost a bit more, but you’ll get great use out of it for years to come. I wouldn’t recommend it to a hobbyist, but for the pros out there that require power, this table saw is going to get the job done.
- 10 inch blade
- Comes with stand
- 30 inch rip capacity
- Pricier than the DeWALT table saw
Best Budget Table Saw
Hobbyists can get away with this table saw like saw that is easy to transport.
- Cuts wood up up to 1-1/2”
- Corded power
- Good for entry-level
On your quest for an affordable table saw, you’ll be surprised at how cheap you can go! You can save a ton of money if you only do small jobs and the Rockwell BladeRunner X2 might just be the table saw for that.
It’s lightweight, coming in at under 15 pounds. You’ll be able to take it with you anywhere.
Switching out blades is super easy, it’ll take you under 10 seconds. The arm comes with 2 knobs, one to raise or lower the arm, and the other to control the blade guard to adjust the height you’re cutting.
This is not a typical table saw with a circular blade, it comes with a jigsaw blade.
It has a 3/4 inch range of motion which is enough for a 2×4. If you just need a few quick cuts here and there, you may not need a pricier model with all the bells and whistles.
You can also use the miter gauge to make miter cuts. One advantage of this is that you can also use the jigsaw blade to make scrolling cuts which wouldn’t be possible with a typical table saw.
It comes with 4 blades that you can change out if you need. It’s also a lightweight table that you can take with you anywhere.
This table saw isn’t the best of the best and that’s obvious. It wasn’t made for any professionals so it comes with some downsides. Some of the cuts may not be perfectly straight which can be a dealbreaker if you’re in the business of perfection.
The guide bearing is flat so there isn’t much to keep the blade steady. This makes the cuts less precise, which can be noticeable. Some purchasers also mentioned that the upper arm is hard to adjust which can cause some annoyance if you’re using this saw often.
Since it isn’t using a 15 amp motor, it’s also going to cut slower than you’d expect. If you’re patient, then it’s fine, but you’re not going to get as much power as other table saws.
If you aren’t a professional and only do hobby-level woodworking, this table saw is an affordable option. You won’t be getting the most accurate cuts out there, but for most entry-level work it’s going to be suitable. It’s not the most powerful, but good enough for some DIY projects here and there.
Remember this isn’t a contractor table, so don’t expect contractor-level precision.
- Comes with 5 blades
- Can do miter cuts
- Not a true table saw
- Not meant for heavy duty work
Do you need a table saw?
Do you need to rip a whole bunch of wood that you can’t otherwise cut with the tools you already own?
If you’re finding yourself spending hours trying to cut through wood with a circular saw as a table saw, then you may be ready for an upgrade.
I understand how tempting it can be to upgrade, but do a cost/benefit analysis and see where you stand.
If you’re a woodworker that is in his/her workshop all day, then you may want to look into a hybrid table saw that has a cast iron table that will cost more, but you won’t have to upgrade ever again.
Make sure you aren’t wearing gloves when operating your saw or you may risk injury. Ensure that you’re working on a stable surface and you have proper eye and hearing protection. Get a table saw that is full of safety features so you need to worry a bit less than normal.
If you feel like you’re tired, then do NOT operate any power tools or table saws under any circumstances. You may feel like you can power through it, but your best bet is to call it a day.
Remember accidents DO happen but when working with powerful table saws, you don’t want to even have one accident!
What to Look for in the Best Table Saws Under 1000?
The type of table saws you’ll be able to find under 1000 are limited. Hybrid table saws are going to be off the table as they’re far too expensive for this budget. You don’t want to skimp either on a hybrid table saw either as they’re meant for heavy duty usage.
What you’ll be able to afford for under $1000 is a job site type table saw. It’ll allow for easy portability, making it great for any professionals out there on the go. Not only that, you won’t need to spend a ton either to get great performance.
There are also affordable table saws that are more like a jigsaw. These are not meant for heavy duty usage, but can come in handy in a pinch or if your budget is fairly limited.
Safety features will keep you safe while you do your job. A blade guard, riving knife, push stick, anti-kickback pawls and sensors are table saw safety features that you should look for.
You may not be able to find one under $1000 though with sensors that automatically turn the blade off if your finger comes in contact with the blade. More expensive hybrid table saws should have all these features.
A rip fence is a cutting guide that helps you cut materials. It’s normally to the right of the blade and runs from the front to the back, and is parallel to the blade.
Rip fences help you make cross cuts. Without a proper rip fence, you’ll have difficulty making accurate cuts as the wood wouldn’t be able to stay in position.
The motor size for table saws that’re affordable is going to range from 5 to 15 amps. The desner the wood you’re working with, the more amps you’re going to want.
15 amps will be more than enough even in workshops that are using table saws all day. Even more expensive hybrid table saws are around 15 amps.
Dust collection is an important feature, keeping your workshop safe and your workspace clean. Most integrated dust collection systems will leave something to be desired.
In scenarios where you’re making a mess in your workshop, a dust collection system will be a great upgrade.
Anyone and everyone can afford table saws if they should they need it. I still think that for everything it offers, the DeWalt Table Saw DWE7485 can’t be beaten!